Carte 2 · Leçon 2 sur 2 · ~6 min
Yield, and why the safety factor goes on the steel
Les leçons sont en anglais pour l'instant.
Bend a paper clip a little and let go: it springs back. Bend it a lot and it stays bent. Somewhere in between, the metal stopped behaving like a spring and started to flow.
Steel does exactly this. The stress at which it stops springing back is its yield strength, Re. A bracket that goes past it is not broken yet, but it is bent for good, and a bent bracket is a failed one.
Tap a symbol to find it in the drawing.
- σ_allow
- the allowable stress: the most you will let the steel carry, in MPa
- Re
- the yield strength: where the steel stops springing back, in MPa
- n
- the safety factor: how many times below yield you stay, no unit
- σ
- the stress in the steel, in MPa
In one sentence
You never design to the yield strength itself: you divide it by a safety factor and design to what is left.
Where it comes from
The picture is what a steel test shows. Pull a sample harder and harder: the stress σ climbs in a straight line while the steel still springs back. At Re the line goes flat, and the steel starts stretching without taking more load. Unload it now and it comes back along the dashed line: shorter than it was, but longer than it started. That is yield.
Why stay far below it? Because every number you design with is a little wrong: the real load, the real steel, the real plate, the hole someone drilled a millimetre off. The safety factor n is the room left for all of it. Divide Re by n and you get the stress you allow: σ_allow = Re / n.
Why on the steel and not on the load? Both are used in real practice. This path puts n on the material so that everyone's working has the same steps and each one can be checked (brief §6).
Check it makes sense
- Units. MPa ÷ a pure number = MPa.
- Bigger
n, smallerσ_allow. More safety means you allow less, so the plate comes out thicker. σ_allowis always belowRe. A safety factor is more than 1.
The trap
Multiplying instead of dividing. Re × n is a stress above yield: a bracket designed to it bends the first day. If your allowable stress is bigger than Re, stop.
And the grade is in the name: S235, S275 and S355 are steels whose yield strength, for plates like ours, is at least the number in the name, in MPa. Different steel, different Re: read it off the brief, never from memory.
Worked, on the practice bracket
The practice bracket is S275 steel with a safety factor of 2.5:
| Working | Result | |
|---|---|---|
| Allowable stress | σ_allow = Re / n = 275 / 2.5 | 110 MPa |
That is step 3 of the challenge, on the practice bracket.
Your turn, half done
A frame of S355 steel, Re = 355 MPa, is designed with a safety factor n = 2. Divide: what stress will you allow?
σ_allow = Re / n = 355 / 2 = 177.5 MPa.
Your turn
A lifting lug is made of S275, Re = 275 MPa. Lifting gear gets a bigger safety factor: n = 3. What is its allowable stress?
σ_allow = Re / n = 275 / 3 = 91.667 MPa.
Check yourself
A classmate does it the other way: multiplies the load by n, and compares the stress with the full Re. What happens to their bracket?
The same thickness. F × n against Re is the same comparison as F against Re / n. It is not wrong engineering, but the brief asks for the allowable stress as step 3, so their step answers would not line up with the ones the checker expects.
What you can do now: say what yield is, and turn a yield strength and a safety factor into an allowable stress. That is step 3 of the wall bracket challenge, done.
Étape 1 sur 11 · ~6 min restantes