Carte 4 · Leçon 2 sur 2 · ~7 min
Two checks, one answer
Les leçons sont en anglais pour l'instant.
You can now work out two things about a plate: whether it is strong enough (Card 3) and how far it sags (lesson 1). The last question is how far is too far, and what to do when the plate strength chose sags past it.
Tap a symbol to find it in the drawing.
- δ_limit
- the most the tip may sag, in mm
- L
- the lever arm, from the centre of the bolts to the load, in mm
- δ
- the tip deflection you worked out, in mm
In one sentence
The tip may sag no more than the bracket's length divided by 300; the plate you use is the thinnest one that is strong enough and stays within that.
Where it comes from
This limit is not about breaking. It is a serviceability limit: a promise about how the part behaves in use. A sag you can see makes people distrust a bracket; a hoist on a sagging arm hangs its chain off line; whatever is fixed to a bendy part cracks. Design codes set limits of this kind, tighter or looser depending on what is attached, as a share of the span. This brief chooses L / 300.
So a plate has two checks, and it must pass both:
- strong enough: its thickness is at least the one Card 3 found;
- stiff enough: its sag
δis at mostδ_limit.
The walk: start at the plate strength chose. Work out its δ. If δ ≤ δ_limit, that is your plate. If not, take the next stock size up and work out δ again. The first plate that passes both checks is the answer to step 8.
Check it makes sense
- Units. mm ÷ a pure number = mm.
- A longer bracket may sag more, but not much more.
δ_limitgrows withL; the sag grows withL³. The longer the arm, the likelier stiffness decides. - The answer is never thinner than step 6. Stiffness can only send you up the list.
The trap
Stopping at step 6. Strength chose a plate, and it is tempting to call it done. On roughly one set of numbers in three, the sag decides instead, and step 8 is a bigger plate.
And "close enough" again. A sag a hair over the limit is over. The practice bracket below misses at one size by less than one per cent.
Worked, on the practice bracket
The practice bracket. The limit first: δ_limit = 440 / 300 = 1.4667 mm. Then the walk up the stock list:
| Plate | Its sag δ | Within 1.4667 mm? |
|---|---|---|
| 8 mm, strength's choice | 1.8423 mm | no |
| 10 mm | 1.4738 mm | no, by a hair |
| 12 mm | 1.2282 mm | yes |
So the practice bracket uses 12 mm plate, not the 8 mm strength asked for. Stiffness decided.
Your turn, half done
A bracket's load hangs 450 mm from the centre of its bolts, and δ_limit = 450 / 300: how far may its tip sag?
450 / 300 = 1.5 mm.
Your turn
The card's final. A bracket 48 mm deep carries 650 N at 560 mm. Strength alone needs 7.2 mm of thickness. The stock is 6, 8, 10, 12, 15 and 20 mm.
Walk up the list from the first plate strong enough: which thickness do you use?
δ_limit = 560 / 300 mm. Strength says 8 mm; at 8 mm and at 10 mm the tip sags past the limit, and at 12 mm it does not. Stiffness decided.
Check yourself
For one bracket, strength asks for 8 mm and stiffness for 12 mm. Which plate goes on the column?
12 mm. A plate is used only if it passes both checks. 8 mm is strong but bendy; 10 mm is not a compromise, it simply fails the stiffness check.
What you can do now: say what a deflection limit is for, and pick the thinnest stock plate that is both strong and stiff enough. That is steps 7 and 8, and the whole calculation of the wall bracket challenge.
Étape 1 sur 11 · ~7 min restantes