Card 3 · Lesson 1 of 3 · ~7 min
How a plate carries a moment
Card 1 ended with a moment at the root, M, in N·mm. Card 2 ended with a stress the steel may carry, σ_allow, in MPa. This lesson joins them.
Bend a thick book: the pages on the outside of the curve slide out, the ones on the inside bunch up. A steel plate does the same. One edge is stretched, the other is squeezed, and a line through the middle is neither.
Tap a symbol to find it in the drawing.
- σ
- the stress at the plate's top and bottom edge, in MPa
- M
- the bending moment the plate carries, in N·mm
- Z
- the section modulus: the plate's shape, as bending strength, in mm³
- σ_allow
- the allowable stress from Card 2, in MPa
In one sentence
The edge stress is the moment divided by the section modulus; to keep it at the allowable stress, the plate needs a section modulus of at least M / σ_allow.
Where it comes from
Look at the triangles in the picture. The stress is zero on the middle line and grows in a straight line to its largest, σ, at the two edges: stretching at the top, squeezing at the bottom. The edges are where the steel works hardest, so the edges are what we check.
How big is σ for a given moment? It depends on the moment, and on the shape of the section: how much steel there is, and how far from the middle it sits. Engineers wrap the shape into one number, the section modulus Z, so that σ = M / Z. The next lesson shows where Z comes from.
To design, turn it round. You know M (Card 1) and the stress you allow (Card 2). The plate must have a Z big enough that the edge stress stays at or below σ_allow: Z = M / σ_allow.
Check it makes sense
- Units. N·mm ÷ MPa = N·mm ÷ (N/mm²) = mm³. A section modulus is always in mm³.
- Twice the moment, twice the
Z. A heavier load needs a stronger shape. - A lower
σ_allowmeans a biggerZ. More safety, more steel.
The trap
Dividing the wrong way. σ_allow / M is a tiny number with no meaning. The moment goes on top: Z = M / σ_allow.
And mixing N·m with MPa. A moment in N·m over MPa gives a number a thousand times too small. Keep the moment in N·mm (Card 1, lesson 2).
Worked, on the practice bracket
The practice bracket, steps 2 and 3 into step 4:
| Working | Result | |
|---|---|---|
| Root moment (step 2) | Card 1 | 107 910 N·mm |
| Allowable stress (step 3) | Card 2 | 110 MPa |
| Section modulus needed | Z = M / σ_allow = 107 910 / 110 | 981 mm³ |
Remember the plate pulled straight in Card 2: 1.0219 MPa. Bent by the same load, the 8 mm plate has Z = 1200 mm³, so its edge stress is σ = M / Z = 107 910 / 1200 = 89.925 MPa. Same load, same plate: bending is what makes a bracket work.
Your turn, half done
A shelf arm carries a moment of 64 000 N·mm. Its steel may carry 125 MPa. So Z = M / σ_allow = 64 000 / 125: what section modulus does it need?
Z = 64 000 / 125 = 512 mm³.
Your turn
Two steps, like the challenge. A sign bracket carries a moment of 88 000 N·mm. It is S275, Re = 275 MPa, with a safety factor of 2.
Step 1: what stress will you allow?
σ_allow = Re / n = 275 / 2 = 137.5 MPa.
Check yourself
Step 2: with that allowable stress, what section modulus must the bracket have?
Z = M / σ_allow = 88 000 / 137.5 = 640 mm³.
Check yourself
Our wall bracket holds its load off the free end. Which edge of the plate is stretched?
The top edge. The load pulls the free end down, so the bracket curves like a frown: the top is stretched and the bottom squeezed. Steel is as strong either way, so the check is the same; but it is the top edge, by the bolts, where a crack in a real bracket starts.
What you can do now: say what the stress in a bent plate looks like, and find the section modulus a plate needs from its moment and its allowable stress. That is step 4 of the wall bracket challenge.
Part 1 of 12 · ~7 min left