Card 2 · Lesson 1 of 2 · ~6 min
Force spread over an area
Hang a heavy bag from a thin string and it cuts into your fingers. Hang it from a wide strap and it doesn't. Same weight, same hand: the difference is how much material the force is shared over.
Steel works the same way. It doesn't care how big a force is. It cares how much force each little piece of it has to carry. That share is called stress, and it is the number a steel's strength is quoted in.
Tap a symbol to find it in the drawing.
- σ
- the stress: how hard each square millimetre is pulled, in MPa
- F
- the force the bar carries, in N
- A
- the area of steel the force is shared over, in mm²
- b
- the width of a flat bar, in mm
- t
- its thickness, in mm
In one sentence
Stress is the force divided by the area that carries it: the same pull on half the steel is twice the stress.
Where it comes from
Cut the bar anywhere across. The part below the cut still hangs there, so the steel across the cut must be holding up the whole force F. No single point holds it all: every square millimetre of the cut takes its share.
Share F newtons out over A square millimetres and each one carries F / A newtons. That share is the stress, σ.
For a flat bar the cut is a rectangle, b wide and t thick, so its area is A = b · t.
Why engineers like N and mm: one newton on one square millimetre is one megapascal, 1 MPa = 1 N/mm². Work in N and mm and the stress comes out directly in MPa, the unit every steel's strength is written in.
Check it makes sense
- Units. N ÷ mm² = N/mm² = MPa.
- Half the area, twice the stress.
Ais underneath: less steel, more stress. - Twice the force, twice the stress.
Fis on top.
The trap
The area in the wrong unit. One square metre is a million square millimetres. Put F in N over A in m² and you get pascals, a million times smaller than MPa, and a bar that looks a million times too strong. Keep N and mm, and the answer is in MPa.
And for a flat bar, multiply width and thickness. Adding them is a length, not an area.
Worked, on the practice bracket
Suppose the practice bracket's plate were not bent at all, but pulled straight by its load, like a hanger:
| Working | Result | |
|---|---|---|
| The area | A = b · t = 30 × 8 | 240 mm² |
| The stress | σ = F / A = 245.25 / 240 | 1.0219 MPa |
About one megapascal, against a steel good for hundreds. Pulled straight, the plate would hardly notice the load. Keep that number in mind: Card 3 shows what bending does to it.
Your turn, half done
A flat bar 10 mm wide and 6 mm thick carries a pull of 1500 N. Its area is 10 × 6 mm². What is the stress?
σ = F / (b · t) = 1500 / (10 × 6) = 25 MPa.
Your turn
A tie bar 12 mm wide and 5 mm thick holds a sign with a pull of 2400 N. What stress is the steel carrying?
A = 12 × 5 mm², so σ = F / A = 2400 / A = 40 MPa.
Check yourself
The same bar, the same pull, but the bar is ground down to half its thickness. What happens to its stress?
It doubles. Half the thickness is half the area, so each square millimetre carries twice the share. The steel is the same; the load on each piece of it is not.
What you can do now: say what a stress is, and work one out in MPa from a force and an area. Next: how much stress a steel can take, and how much of that you should allow.
Part 1 of 11 · ~6 min left